ENR 1.5 HOLDING, APPROACH AND DEPARTURE PROCEDURES

1 General

1.1 General instructions
1.1.1 The holding, approach and departure procedures in use are based on those contained in the latest edition of ICAO Doc 8168 — Procedures for Air Navigation Services — Aircraft Operations (PANS-OPS).
1.1.2 The holding and approach procedures in use have been based on the values and factors contained in Part III and IV of Vol. I of PANS-OPS, except for transition layer. The holding patterns shall be entered and flown as indicated below.
Flight level (FL)Category A and B aircraftJet aircraft
Normal conditionsTurbulence conditions
Up to 13 000 FT (3 950 M) inclusive170 KT230 KT (425 KM/H)280 KT (520 KM/H) or Mach 0.8, whichever is less
Above FL 150 (4 550 M) m to FL 200 (6 100 M) inclusive240 KTkt (445 KM/H)
Above FL 200 (6 100 M) to FL 240 (7 300 M) inclusive265 KTkt (490 KM/H)
1.2 Naming convention for waypoints used in RNP instrument approach procedures
1.2.1 In accordance with ICAO Document 8168, Vol II, Part III, Section 5, Chapter 1, 1.6 - WAYPOINT NAMING criteria, following convention applies for naming waypoints in RNP Instrument Approach Procedures that are designated by alphanumeric name-code:

1. For missed approach points (MAPt’s) co-located with RWY THR:

  1. First two (2) alphabetic characters - “RW”
  2. Last two (2) or three (3) characters - corresponding RWY designator.

e.g. “RW16L”, “RW34R”, “RW15”, “RW33”

2. For other waypoints unique to a specific aerodrome:

  1. First two (2) characters – the third and fourth letters of ICAO location indicator of the aerodrome.
  2. Last three (3) characters – any combination of numeric characters from 401 to 999 but not ending with zero (0) or five (5).

e.g. for Doha International Airport “BD401” or “BD701”; for Hamad International Airport “HH501” or “HH801”

2 Arriving flights

2.1 Instructions
2.1.1 All traffic landing within Doha TMA may expect Continuous Descent Operation (CDO) on following enroute segments.
  1. L564/UL564 – BATHA to LADEMPASOM
  2. M430/UM430 – ULIKA to GINTO
2.1.2 IFR flights (inclusive FL 150 and above) landing within Doha TMA, will be cleared to a specific holding fix or as instructed by "DOHA RADAR" and may expect further instructions from "DOHA APPROACH" and/or "DOHA DIRECTOR" subsequently.
2.1.3 IFR flights (below FL 150) landing within Doha TMA, will be cleared to a specific holding fix or to a STAR as instructed by "DOHA APPROACH" and expect further clearance from "DOHA DIRECTOR".
2.1.4 Holding procedure shall be carried out with the authorized level until further instructions given by "DOHA RADAR" or "DOHA APPROACH".
2.1.5 Due to the limited airspace within Doha TMA, it is important that all arrivals to the patterns and for the holding procedures are to be carried out as precisely as possible. Pilots are advised to inform ATC if unable to comply with this requirement.
2.2 Speed requirement
2.2.1 All aircraft entering Doha TMA are required to adjust IAS as per the following speeds unless otherwise instructed by ATC:
  1. 210 - 230 KT during the initial approach phase;
  2. 180 KT on base leg / closed heading to final approach and
  3. 160 KT when established on final approach and thereafter 160 KT to 5 NM final.
2.2.2 These speeds are applied for ATC separation purposes and are recommended.
2.2.3 All speed restrictions are to be flown as accurately as possible. Aircraft unable to conform to these speeds must inform ATC and state what speeds can be used. Pilots should also advise ATC if circumstances necessitate a change of speed for aircraft per reasons.
2.2.4 In the interests of accurate spacing, pilots are requested to comply with speed adjustments as promptly as feasible within their own operational constraints.
2.2.5 In the event when traffic sequencing does not require speed limitation, ATC will advise " NO ATC SPEED RESTRICTION".

3 Departing flights

3.1 GENERAL
3.1.1 IFR flights departing from controlled aerodrome will receive initial ATC clearance from the local Aerodrome Control Tower. The clearance limit will normally be the aerodrome of destination.
3.2 INSTRUCTIONS
3.2.1 All OTBD/OTHH departure aircraft shall immediately contact DOHA APPROACH on 119.725 MHz.
3.2.2 On initial contact with DOHA APPROACH, aircraft from OTBD/OTHH must include the following on their DEPARTURE REPORT:
  1. Aircraft call sign;
  2. Passing altitude and
  3. Designated SID
3.2.3 Detailed instructions with regards to routes, turns etc. will be issued by DOHA APPROACH.
3.3 SPEED REQUIREMENT
3.3.1 All OTHH/OTBD departure aircraft are required to maintain maximum 250250KT KIASIAS until passing 10 000 FT unless otherwise instructed by ATCATC or required by Standard Instrument Departure Procedure.
3.3.2 All traffic departing OTHH/OTBD via B457/UB457 and M444/UM444 are required to cross DENVO at FL180 or above and not to exceed 300 KIASKT IAS .
3.4 PHRASEOLOGY AND PROCEDURES
3.4.1 Pilots shall respond to “CLIMB UNRESTRICTED” clearances by repeating the clearance verbatim and expected to commence an unrestricted climb to comply with the clearance.
3.4.2 For aircraft already climbing via the SIDSID published altitude, restrictions are deleted unless reissued by ATCATC.